Heater Chiller Circulator
Heater chiller circulator is a temperature control device used in the chemical industry to heat the reactor for different periods of time. It is easy to operate and can quickly improve the heating and cooling speed and temperature distribution accuracy. It is a suitable device for high temperature and low temperature working conditions.
| Send an E-mail to us! | |
Follow Us:
|
|
 ( Click this button to inquiry ) |
|
PRODUCTS
- Glass Reactor Series
- Rotary Evaporator Series
- Water Vacuum Pump Series
- High and Low Temperature Cycling
- Cooling Liquid Circulating Pump Series
- Circulating Water or Oil Bath Series
- Drying Oven
- Hydrothermal Synthesis Reactor
- Microwave Chemical Reactor
- High Pressure Reactor Series
- Short Path Distillation
- Heating Mantle
- Spray Dryer
- Solvent Recovery Machine
- Stainless Steel Reactor
- Other
- Emulsifying Mixer Machine
Whatsapp:+8615036470528
E-mail: [email protected]
Address: 19/F, Block B, Guohong Mansion, Northeast corner of the intersection of Huagong Road and Lamei Street, Hi-Tech Development Zone, Zhengzhou City, Henan Province, China
The heater chiller circulator uses a pump to drive the heat transfer medium (usually water, ethanol, silicone oil, etc.) from the oil tank with a built-in heater to the temperature control device, and then returns to the oil tank from the temperature control device.
Heater chiller circulator Since the entire liquid circulation is a closed system, there is no water vapor absorption at low temperature, and no oil mist generation at high temperature.
Realize continuous temperature rise and fall, adopt high temperature and high pressure operation compressor technology, can directly turn on compressor refrigeration from 350 degrees, high and low temperature cycle integrated machine can greatly provide cooling rate, save test time and energy.
The heater chiller circulator operation uses:
1) Regardless of whether it is air-cooled or water-cooled, the temperature control device must be located in an operating environment with sufficient fresh air: a space greater than 30cm around.
2) When choosing a heat transfer medium, pay attention to whether its upper and lower temperature limits, ignition point, viscosity, freezing point, etc.
3) Heater chiller circulator When selecting a heat transfer pipe, the length should be as short as possible, and the diameter should be as large as possible. If the diameter is too small, it may cause current restriction;
4) Do not use water as heat transfer medium for heater chiller circulator;
5) Unsuitable heat transfer media will have a negative impact on the equipment and may cause damage to the device.
6) The equipment adjustment parameters must be reset after filling, which is a requirement for correct operation and use of the instrument;
7) Regularly check the heat transfer pipes of the heater chiller circulator to avoid material damage (such as fission).
Heater chiller circulator features:
1. The heater chiller circulator is equipped with an integrated heating and cooling container, with a large heat exchange area, fast heating and cooling rates, and relatively small demand for heat transfer oil.
2. It can realize continuous heating and cooling, and adopts the technology of operating the compressor under high temperature and high pressure.
3. The whole cycle is airtight, there is no oil mist volatilization at high temperature, and the heat transfer oil is not easy to be oxidized and browned.
5. Heater chiller circulator temperature adaptive control.
7. The heater chiller circulator uses no CFC and HCFE refrigerant.
8. Control the speed of the chemical reaction.
9. The cost of use is low.
10. Liquid circulation pipes and heating pipes are made of high-quality industrial-grade seamless 304 stainless steel with a thickness of 3.0mm, which are definitely not decorative pipes.
11. The refrigeration system adopts Gulun compressor from the United States, Taikang from France, and high-temperature-resistant circulation pump, with stable performance and reliable quality.
12. Wide working temperature range, with heating and cooling functions at the same time, the maximum temperature range: -95 ~ 350 degrees.
13. The heater chiller circulator can simultaneously display the temperature setting value and actual value, as well as the over-temperature alarm value.
14. The liquid filling is efficient and fast, and the liquid filling is simple.
15. Ensure rapid cooling under high temperature conditions; it can realize continuous temperature control from 350 degrees to -95 degrees to save test production time.
16. Liquid circulation pipes and heating pipes are made of high-quality industrial-grade seamless 304 stainless steel with a thickness of 3.0mm, which is by no means an ordinary decorative pipe.
Technical Parameter
| Model | GDSC-1005 |
| Suitable for reactor volume (L) | 100L |
| Cycle way | - 10℃—200℃ |
| Display accuracy | 0.1℃ |
| Cooling capacity | 500-1500W |
| Heating power | 3KW |
| Lift (m) | 8—12m |
| Flow (L/Min) | 25—30L/Min |
| Temperature control form | Microcomputer digital control |
| Safety protection | Have delay , leakage, over current, overheating production |
| Refrigeration components | Fully enclosed Compressors |
| Circulation pump | Fully enclosed special pump without leakage |
| Total power (W) | 4000W |
| Supply voltages | 220V 50HZ |
